SANWA MX-6 RADIO SET WITH RX-391W

SYSTEM: 2.4GHz Computer System FH4/FH3, CH: 4CH, TRANSMITTER: TX-452, RECEIVER: RX472 

We have the early information on the new SANWA MT-5 mid level wheel radio set.

We are now taking pre-orders via dealers.

Due middle of February.

Compatible Response Mode with SUR, SSR, SHR, NOR
SSL CODE5/CODE10 Function
Quick Setup Wizard
Full Adjustable Trigger
Adjustable Steering and Throttle Tension
INDICATOR FUNCTION can show Receiver Signal Strength and Packet Delivery Ratio
Weight: 382 g
Power source: AAA Battery x 3
ONLY Compatible RF with FH5
Includes new RX-493i receiver

One of the outstanding feature of MT-5 is the indicator function which can check signal receiving condition with using RX-493i.
The conditions can be used for checking device and correct receiver placement.

SANWA RX-472 Telemetry/SSL Receiver 

- 2.4GHz FHSS4/FHSS3 Spread spectrum system 4ch 
- Sanwa Synchronised Link ( SSL ) function support 
- Sanwa Super Response (SSR) support 
- Lightest receiver in class 

Frequency - 2.4GHz FHSS4/FHSS3 
Channel - 4ch 
Nominal Input Voltage - 4.8~7.4V 
Dimensions - 30.0x23.3x14.0mm 
- 6.6g 
Compatible radio - M12, EXZES Z, MT-4 ( SSL not support ) 
SSL Function (Sanwa Synchronised Link) System From using both of "RX-472" and "Super Vortex Zero", Drivers operate "Code AUX Function" which is included on M12 & EXZES-Z and can adjust setting of equipment directly and quickly from Radios. 
In case of using SSL System, Drivers don't need to use Setting Card or PC. And also, Telemetry data can be sent to Radios without using any Sensors. 

In case of using MT-4 with both of "RX-472" and "Super Vortex Zero", SSL Function is not responded, but Telemetry data can be sent to Radios without using any Sensors.

- 2.4GHz FHSS4/FHSS3 Spread spectrum system 4ch
- Built-in Antenna
- Sanwa Super Response (SSR) support

Frequency - 2.4GHz FHSS4/FHSS3
Channel - 4CH
Nominal Input Voltage - 3.7V~7.4V
Dimensions - 18.2x24.4x27.1mm
Weight - 7.1g
Compatible radio - M12, EXZES Z, M11X, EXZES X, MT-4S, MT-4, GEMINI X

RX-482 Telemetry/SSL Receiver

- 2.4GHz FHSS4 Spread spectrum system 4ch
- SSL support (ESC: Super Vortex Series etc.)
- Built-in Antenna
- Sanwa Super Response (SSR) support

Frequency - 2.4GHz FHSS4
Channel - 4ch
Nominal Input Voltage - 3.7V~7.4V
Dimensions - 18.2x24.4x27.1mm
Weight - 7.1g
Compatible radio - M12, Exzes Z, MT-4S, MT-4(No SSL support)

RX-481WP - Built in Antenna Receiver

- 2.4GHz FHSS4/FHSS3 Spread Spectrum System 4CH
- Super Response (SSR) Mode-Compatible
- Waterproof (IPX4)

- Frequency - 2.4GHz FHSS4 / FHSS3
- Nominal Input Voltage - 3.7-7.4V
- Weight - 10.7g
- Channel - 4CH
- Dimensions - 21.4x27.6x29.4mm
- Compatible radio - M12S, M12, EXZES ZZ, EXZES Z, M11X, EXZES X, MT-4S, MT-4, MT-S, MX-3X, GEMINI X

The RX-493 receiver includes coaxial antenna and pipe for greater range and more stability.

The RX-493 is compatible with FH5/FH5U system for M17 radio ONLY.

Compatible with SXR response mode.

Voltage 4.8-7.4v and water proof (as IPX4) Compatible with SSL function.

Easy install antenna pipe.

26x23.2x14mm
6.2g
Recommended pipe length 100mm

FH5U: SXR(SANWA XTREME RESPONSE) MODE-COMPATIBLE
- SSL-COMPATIBLE PROGRAMMABLE SERVO
# Compatible with CODE 10 (M12S, EXZES ZZ, MT-44)
Not Compatible with CODE 5 (M12, EXZES Z, MT-4S, MT-4, MT-S)
- PGS SETTING GEAR-COMPATIBLE
- SUPER RESPONSE (SSR) MODE-COMPATIBLE
- HIGH RESPONSE (SHR) MODE-COMPATIBLE
- Li-Po 2 CELL-COMPATIBLE
- HIGH TORQUE TYPE
- BRUSH LESS MOTOR
- FULL ALUMINUM CASE
- FULL METAL GEAR (Strengthening Gears)
- AL HEAT SINK
- Black Harness

Programmable Servo to be compatible with SSL & Telemetry at Launch
- Setting Adjustment by wireless from Radio
- Setting Adjustment to connect Servo with Setting Gear
- Regarding Temperature, Current, Voltage and Volume Position on Servo inside,
Telemetry-transmission can be passed to Radio.
# Initial Setting on Setting Gear is necessary.

- Setting Items
- SSL-CH (SSL Channel Setting) - STRETC (Stretcher Adjustment) ?BOOST (BOOST Adjustment)
- D-Band (Dead Band Adjustment) - MV-MID (Middle Torque Adjustment)
- MV-END (Later Torque Adjustment) - BREAK (Break Adjustment)
?MV-HOLD (Power Adjustment at whole area) ?MV-FRQ (Feeling Adjustment at whole area)
?MAX-PW (MAX Duty Adjustment)
? Setting Gear is necessary for ?setting.

Speed
0.08 sec/60 (7.4V)
0.11 sec/60 (6.0V)

Torque
16.6 kg/cm (7.4V)
14.7 kg/cm (6.0V)

Dimensions
40.5 x 20.5 x 26.5 mm

Weight
49.6 g

SSL Compatible
- Compatible with CODE10 (M12S (RS), Exzes ZZ, MT-44)
Not compatible with CODE5 (M12, Exzes Z, MT-4S, MT-4, MT-S)
- MULTI SETTING GEAR compatible
Not compatible with PGS SETTING GEAR
- SSR mode compatible
- SHR mode compatible
- Lipo 2 cell battery compatible
- High torque type
- Coreless motor
- Metal Gears
- AL Heat Sink

Programmable Servo to be compatible with SSL & Telemetry
- Setting Adjustment by wireless from Radio
- Setting Adjustment to connect Servo with Multi Setting Gear
- Regarding Temperature, Current, Voltage and Volume Position on Servo inside,
Telemetry-transmission can be passed to Radio.
# Initial Setting on Multi Setting Gear is necessary.

- Setting Items
- SSL-CH (SSL Channel Setting) - STRETC (Stretcher Adjustment) - BOOST (BOOST Adjustment)
- D-Band (Dead Band Adjustment) - MV-MID (Middle Torque Adjustment)
- MV-END (Later Torque Adjustment) - BREAK (Break Adjustment)
?MV-HOLD (Power Adjustment at whole area) ?MV-FRQ (Feeling Adjustment at whole area)
?MAX-PW (MAX Duty Adjustment)
- Multi Setting Gear is necessary for setting.

Speed
0.11 sec / 60° (7.4 V)
0.13 sec / 60° (6.0 V)

Torque
26.5 kg ·cm (7.4 V)
23.3 kg ·cm (6.0 V)

Dimensions
40.5 X 20.5 X 37.2 mm

Weight
59 g

SANWA PGS-HR Servo

- Digital Servo
- Coreless Motor
- Full metal gear
- LiPo (1 & 2cell)
- PGS SETTING GEAR-COMPATIBLE


Speed
0.10 sec / 60° (6.0 V)
0.16 sec / 60° (3.7 V)

Torque
3.8 kg·cm (6.0 V)
5.8 kg·cm (3.7 V)

Dimensions
27.0 x 21.1 x 30.5 mm

Weight
24 g

Sanwa Radio Bag complete with shoulder strap.